README.md

@@ -1,6 +1,6 @@
-# Flag Clip (Revised)
+# flag-clip
 
-Hybrid clip / carabiner 3D printable model to attach flags to the cable of a flag pole.
+Hybrid clip / carabiner 3D printable model to attach flags to the rope of a flag pole.
 
 The gate of the carabiner does double duty as the lever of the clip.
 
@@ -9,16 +9,7 @@ Spring mechanism inspired by [https://www.thingiverse.com/thing:1212828/remixes]
 Since this was intended for outdoors use, I've printed this in PETG.
 
 ![](img/clip.jpeg)
-
-OpenSCAD file enclosed for tuning. In particular, the diameter of the eye at the bottom needs to be closely matched to the flag cable diameter.
-
-# Installation
-
-![](img/install_1.jpeg)
-![](img/install_2.jpeg)
-![](img/install_3.jpeg)
-![](img/install_4.jpeg)
-![](img/install_5.jpeg)
+![](img/flag.jpeg)
 
 ## Revision History
 
@@ -29,7 +20,3 @@ Initial Design
 ### 2022-07-04 Version 2.0
 
 Substantial Revision. It turns out that even a moderate wind was enough to pull the flag off the pole with the initial design. This revision is considerably more robust to wind, though it still failed in a heavy thunderstorm.
-
-### 2023-08-15 Version 4.0
-
-Revised again (Rev v3 was unsuccessful). This time tested through an entire season's worth of storms.

flagclip.scad

@@ -1,173 +0,0 @@
-/*
- * Flagclip - Flag attachment carabine
- *
- * Copyright (C) 2022-23 Matthias Neeracher <microtherion@gmail.com>
- */
-
-$fn= $preview ? 32 : 64;
-
-// Diameter of flagpole wire
-wire_dia        = 3.9;          // [1.0:0.05:7.0]
-
-/* [Other Parameters - Tune if Needed] */
-// Thickness (Z)
-thickness       = 4.0;          // [3.0:0.25:8.0]
-// Width of outer walls
-wall            = 4.0;          // [2.0:0.25:6.0]
-// Gaps for carabine and spring openings
-gap             = 1.0;          // [0.5:0.25:2.0]
-
-/* [Spring Parameters - Tune if Needed] */
-// Spring Center Radius
-spring_center   = 3.0;          // [2.0:0.5:10.0]
-// Gap Between Inner and Outer Rings
-spring_gap      = 3.0;          // [1.0:0.5:5.0]
-
-/* [Carabine Parameters - Tune if Needed] */
-// Aperture Angle of Carabine Loop
-cara_aperture   = 45.0;         // [30:5:90]
-// Length of Carabine Arm
-cara_arm        = 15.0;         // [10:5:50]
-
-/* [Clip Parameters - Tune if Needed] */
-// Width of Inner Gap for Clip
-clip_aper       = 2.5;          // [1.0:.5:10]
-// Width of Clip at Bottom of Opening
-clip_base       = 12.0;         // [10.0:50.0]
-// Length of Clip Arm
-clip_arm        = 18.0;         // [15.0:50.0]
-// Arc of Wire Holder
-clip_arc        = 290;          // [190.0:10:330]
-// Width of Wire Holder Walls
-clip_wall       = 2.0;          // [1.0:0.25:4.0]
-// Clearance of Gap from Edge of Spring
-clip_clear      = 4.0;          // [1.0:1.0:10.0]
-// Vertical Displacement of Clip Gap
-clip_lever      = 4.0;          // [0.0:0.25:6.0]
-
-function intersect_circle(p0, v, r) =
-    let (num = sqrt((r^2-p0[0]^2)*v[1]^2+2*p0[0]*p0[1]*v[0]*v[1]+(r^2-p0[1]^2)*v[0]^2)-p0[1]*v[1]-p0[0]*v[0],
-         l = num/(v[1]^2+v[0]^2)) p0+l*v;
-
-function intersect_lines(p0, v, q0, w) =
-    let (l = (-q0[0]*w[1]+p0[0]*w[1]+(q0[1]-p0[1])*w[0])/(v[1]*w[0]-v[0]*w[1])) p0+l*v;
-
-module flagclip(wire_dia=wire_dia, thickness=thickness, wall=wall,
-                spring_center=spring_center, spring_gap=spring_gap,
-                cara_aperture=cara_aperture, cara_arm=cara_arm,
-                gap=gap,
-                clip_aper=clip_aper, clip_base=clip_base, clip_arm=clip_arm,
-                clip_arc=clip_arc, clip_wall=clip_wall, clip_clear=clip_clear,
-                clip_lever=clip_lever)
-{
-    spring_inner_in_r  = spring_center;
-    spring_inner_out_r = spring_inner_in_r + wall;
-    spring_outer_in_r  = spring_inner_out_r + spring_gap;
-    spring_outer_out_r = spring_outer_in_r + wall;
-
-    cara_ratio_r       = [sin(0.5*cara_aperture), cos(0.5*cara_aperture)];
-    cara_ratio_out_r   = [cos(0.5*cara_aperture), -sin(0.5*cara_aperture)];
-    cara_inner_bot_r   = [0.5*spring_gap, spring_outer_in_r*cos(asin(0.5*spring_gap/spring_outer_in_r))];
-    cara_inner_top_r   = cara_inner_bot_r+cara_arm*cara_ratio_r;
-    cara_outer_top_r   = cara_inner_top_r+wall*cara_ratio_out_r;
-    cara_outer_top_rp  = cara_inner_top_r+(wall+1)*cara_ratio_out_r;
-    cara_outer_bot_r   = cara_outer_top_r-(cara_arm-0.5*wall)*cara_ratio_r;
-    cara_ratio_l       = [-sin(0.5*cara_aperture), cos(0.5*cara_aperture)];
-    cara_ratio_out_l   = [-cos(0.5*cara_aperture), -sin(0.5*cara_aperture)];
-    cara_inner_bot_l   = [-cara_inner_bot_r[0], cara_inner_bot_r[1]];
-    cara_inner_top_l   = cara_inner_bot_l+cara_arm*cara_ratio_l;
-    cara_outer_top_l   = cara_inner_top_l+wall*cara_ratio_out_l;
-    cara_outer_top_lp  = cara_inner_top_l+(wall+1)*cara_ratio_out_l;
-    cara_outer_bot_l   = cara_outer_top_l-(cara_arm-0.5*wall)*cara_ratio_l;
-    cara_inner_gap_l   = cara_inner_bot_l+(cara_arm-gap)*cara_ratio_l;
-    cara_outer_gap_l   = cara_inner_gap_l+wall*cara_ratio_out_l;
-    cara_loop_center   = [0,cara_inner_top_r[1]];
-    cara_loop_in_r     = cara_inner_top_r[0];
-    cara_loop_out_r    = cara_loop_in_r+wall;
-
-    clip_half_aperture = asin(0.5*(clip_base-clip_aper)/clip_arm);
-    clip_ratio_r       = [sin(clip_half_aperture), -cos(clip_half_aperture)];
-    clip_ratio_out_r   = [-clip_ratio_r[1], clip_ratio_r[0]];
-    clip_inner_in_r    = [0.5*clip_aper, -spring_inner_in_r*cos(asin(0.5*clip_aper/spring_inner_in_r))];
-    clip_inner_in_l    = [-clip_inner_in_r[0], clip_inner_in_r[1]];
-    clip_inner_out_r   = [0.5*clip_aper, -spring_inner_out_r*cos(asin(0.5*clip_aper/spring_inner_out_r))];
-    clip_inner_out_l   = [-clip_inner_out_r[0], clip_inner_out_r[1]];
-    clip_bot_in_r      = clip_inner_out_r+clip_arm*clip_ratio_r;
-    clip_bot_out_r     = clip_bot_in_r+wall*clip_ratio_out_r;
-    clip_inner_r       = clip_bot_out_r-(clip_arm+0.5*wall)*clip_ratio_r;
-    clip_inner_inter_r = intersect_circle(clip_inner_r, clip_ratio_r, spring_inner_out_r);
-    clip_ratio_l       = [-clip_ratio_r[0], clip_ratio_r[1]];
-    clip_ratio_out_l   = [clip_ratio_l[1], -clip_ratio_l[0]];
-    clip_bot_in_l      = clip_inner_out_l+clip_arm*clip_ratio_l;
-    clip_bot_out_l     = clip_bot_in_l+wall*clip_ratio_out_l;
-    clip_inner_l       = clip_bot_out_l-(clip_arm+0.5*wall)*clip_ratio_l;
-    clip_outer_inter_l = intersect_circle(clip_inner_l, clip_ratio_l, spring_outer_out_r);
-    clip_inner_inter_l = intersect_circle(clip_inner_l, clip_ratio_l, spring_inner_out_r);
-    clip_outer_gap_t   = clip_outer_inter_l+clip_clear*clip_ratio_l;
-    clip_outer_gap_b   = clip_outer_gap_t+gap*clip_ratio_l;
-    clip_inner_gap_t   = clip_outer_gap_t-wall*clip_ratio_out_l-clip_lever*clip_ratio_l;
-    clip_inner_gap_b   = clip_inner_gap_t+gap*clip_ratio_l;
-    wire_center        = [0, clip_bot_in_r[1]+0.5*wire_dia];
-    clip_angle         = 180-0.5*clip_arc;
-    wire_ratio         = [sin(clip_angle), cos(clip_angle)];
-    wire_out_r         = clip_wall*[wire_ratio[1], -wire_ratio[0]];
-    clip_wire_inter_r  = intersect_lines(clip_bot_in_r, clip_ratio_r, wire_center, wire_ratio);
-    clip_wire_inter_l  = [-clip_wire_inter_r[0], clip_wire_inter_r[1]];
-    wire_out_l         = clip_wall*[-wire_ratio[1], -wire_ratio[0]];
-
-    linear_extrude(height=thickness) {
-        /* Spring */
-        difference() {
-            union() {
-                difference() {
-                    circle(r = spring_outer_out_r);
-                    circle(r = spring_outer_in_r);
-                }
-                circle(r = spring_inner_out_r);
-                translate([-spring_outer_in_r-1,-0.5*wall,0])
-                    square(size=[2*spring_outer_in_r+2, wall]);
-            }
-            circle(r = spring_inner_in_r);
-            /* Opening for Carabine */
-            polygon(points=[cara_inner_bot_r, cara_inner_top_r, cara_inner_top_l, cara_inner_bot_l]);
-            /* Opening for Clip */
-            polygon(points=[clip_inner_in_l, clip_inner_out_l, clip_bot_in_l, clip_bot_in_r, clip_inner_out_r, clip_inner_in_r]);
-            polygon(points=[clip_inner_gap_b, clip_inner_gap_t, clip_outer_gap_t, clip_outer_gap_b]);
-        }
-        /* Carabine */
-        difference() {
-            translate(cara_loop_center) circle(r = cara_loop_out_r);
-            translate(cara_loop_center) circle(r = cara_loop_in_r);
-            polygon(points=[cara_outer_top_rp, cara_inner_top_r, cara_loop_center, cara_inner_top_l, cara_outer_top_lp, [cara_outer_top_l[0], 0], [cara_outer_top_r[0], 0]]);
-        }
-        polygon(points=[cara_outer_bot_r, cara_outer_top_r, cara_inner_top_r, cara_inner_bot_r]);
-        polygon(points=[cara_outer_bot_l, cara_outer_gap_l, cara_inner_gap_l, cara_inner_bot_l]);
-        /* Clip */
-        difference() {
-            translate(clip_bot_in_r) circle(r=wall);
-            translate([clip_bot_in_r[0]-wall, clip_bot_in_r[1]-wall]) square(size=[wall, 2*wall]);
-        }
-        polygon(points=[clip_bot_in_r, clip_bot_out_r, clip_inner_inter_r, clip_inner_out_r]);
-        difference() {
-            translate(clip_bot_in_l) circle(r=wall);
-            translate([clip_bot_in_l[0], clip_bot_in_r[1]-wall]) square(size=[wall, 2*wall]);
-        }
-        difference() {
-            polygon(points=[clip_bot_in_l, clip_inner_out_l, clip_inner_inter_l, clip_bot_out_l]);
-            polygon(points=[clip_inner_gap_b, clip_inner_gap_t, clip_outer_gap_t, clip_outer_gap_b]);
-        }
-        translate([clip_bot_in_l[0], clip_bot_in_l[1]-wall]) square(size=[clip_base, wall]);
-        difference() {
-            union() {
-                translate(wire_center) circle(r=0.5*wire_dia+clip_wall);
-                polygon(points=[wire_center, wire_center+wire_out_r, clip_wire_inter_r+wire_out_r, clip_wire_inter_r]);
-                polygon(points=[wire_center, clip_wire_inter_l, clip_wire_inter_l+wire_out_l, wire_center+wire_out_l]);
-            }
-            translate(wire_center) circle(r=0.5*wire_dia);
-            polygon(points=[wire_center, clip_wire_inter_r, clip_wire_inter_l]);
-            translate(clip_wire_inter_l) square([clip_base, wall]);
-        }
-    }
-}
-
-flagclip();